Goodwood Audio Goodwood Audio LongLine Junction Box and DI

Presenting the Goodwood Audio LongLine Junction Box and DI. Want flexible outputs across mono, dual mono and stereo? Want these options across both balanced XLR and unbalanced 1/4" outputs? Need to be able to use these across both instrument and line level? LongLine is the answer. LongLine Outputs Both the XLR outputs and 1/4" outputs are mirrored. The left input will send both left 1/4" and left XLR outputs. Same goes for the right input and outputs. This also means the sum push button will work across all outputs (XLR and 1/4"). The XLR outputs on LongLine can be used for two main purposes regardless of what summing mode you are using: 1. Active DI - You can use the XLR outputs as a pair of active DIs and plug straight into a sound desk, interface or DAW. Use the -20dB Pad pushbutton if signal level is too hot. LongLine's outputs are phantom power protected, so you can play in peace without worrying about busy sound engineers accidentally sending 48v to your board! 2. Line Driver - Tube amps sound great when they are pushed. A lot of venues / studios don't have the ability to facilitate loud amp levels during gigs. With LongLine you can send your guitar signal up to 300 feet (90 meters) to your amp without signal loss. This means you can run your amp in a completely different room, or building and ideally turn it up as loud as you need to get the best tone out of your rig. Use RCV to convert your signal back to unbalanced 1/4" right before your amps input. Do NOT use the pad pushbutton (leave it out) in this mode. Summing LongLine has two types of summing: Stereo Sum and Split Sum. To access these two modes, use the internal DIP switch to select which mode is best for you. You can also access Mix Mode with the DIP switches as well. The Sum switch is global - it acts across all four outputs - XLR and 1/4". 1. Stereo Sum (DIP Sw UP) – This is the default mode LongLine ships with. In this mode use stereo effects as normal. When summed, the left and right inputs are merged and the exact same signal is sent to the left and right outputs. Better for stereo delays and reverbs. 2. Split sum (DIP Sw DOWN) – Still use stereo effects as normal. When summed, the right input is ignored and the left input is split to both left and right outputs. Typically better for stereo modulation. 3. Mix Mode - With the left DIP UP and the right DIP DOWN you are in mix mode. In this mode you can take signals from two different sources (Maybe a dry signal coming into the left input and a wet signal into the right input) and mix them. This is different to summing, so please use this mode if you want to mix! Lastly, if you want to run stereo XLR but mono 1/4" you can do this too! Simply leave the white 'sum' pushbutton in stereo mode (out) and plug in the left 1/4" jack only. This will 'Stereo Sum' the left and right 1/4" signal to an amp, DI or monitor while maintaining a stereo signal on the XLR outputs. Ground Lift & Phase Correction LongLine comes standard with ground lift and phase on all 4 outputs. This means the ground lift and phase push buttons will work on both the XLR and 1/4" outputs at the same time! Ground Lift – A ground loop is never a welcome sound - a loud buzz when two outputs are being used at certain venues - but it doesn't have to waste your time. Simply push the black pushbutton in on LongLine and the ground loop will be eliminated! Phase Correction – When using multiple amps or outputs it is possible that the outputs being used are out of phase with each other. With amps this is easily demonstrated by one amp speaker moving in while the other is moving out. Correct this easily by pushing the red pushbutton in - inverting the phase on one amp by 180 degrees. IMPORTANT - Use only 9vDC centre negative plug to power! The voltage doubles internally for higher headroom! Current Draw/Power: 75mA, Center Neg 2.1mm Dimensions: 120mm x 94mm x 34mm Input Impedance (Left In, Right In): 1Meg Output Impedance (1/4" Outputs): 500ohms Output Impedance (XLR Outputs): Low